Yellow Washer & Nut

August 17, 2015 by  
Filed under GHWT Drum Parts

Yellow Cymbal Washer & Nut World Tour drum kit.

 

These specially made cymbal nuts and washers are used to attach the cymbals to the right and left sides of the World Tour drum kits. This yellow washer & nut is used on the left hand side of the drum kit.
Yellow Cymbal Washer and Nut Replacement FAQ's

  • Do I get instructions with my order?

No, these just screw onto the cymbal arm to hold on the cymbal

  • What tools will I need?

None

  • Do I need any special skills to fit this item?

No

  • Is this kit compatible with the Band Hero drum kit?

Yes

Orange Washer and Nut

August 17, 2015 by  
Filed under GHWT Drum Parts

Orange Cymbal Washer & Nut World Tour drum kit.

 

These specially made cymbal nuts and washers are used to attach the cymbals to the right and left sides of the World Tour drum kits. This orange washer & nut is used on the right hand side of the drum kit.
Orange Cymbal Washer and Nut Replacement FAQ's

  • Do I get instructions with my order?

No, these just screw onto the cymbal arm to hold on the cymbal

  • What tools will I need?

None

  • Do I need any special skills to fit this item?

No

  • Is this kit compatible with the Band Hero drum kit?

Yes

Upgraded Band Hero Replacement Cymbal Cable

August 17, 2015 by  
Filed under GH6 Drum Parts, Site Details

2015-08-17 12.37.17

One of the most common breakages on a Guitar Hero Band Hero drum kit is the cymbal cable. You know the story, you unscrew one of the cymbals, pull it off and forget there is a delicate cable in the bottom of it and... too late! If you are not sure if it is your cymbal cable or inside the drumkit that is broken try swapping the cymbal from the opposite side.

Our replacement cymbal cables are made of much thicker wire, feature a larger plug head which is much stronger, and they are also longer so you can safely take the cymbal off and get to the cable, before you have broken it, we have yet to break one of these!

The fit is universal, meaning you do not need to choose a left or right hand side cable, one size really does fit all, and is compatible with all Band Hero drum kits (Sony Playstation 2 & PS3, Xbox 360, Nintendo Wii)

Fitting Instructions

It really couldn't be easier; using a small screwdriver take off the back of the cymbal (some use a small Phillips head and some use a T10 Torx,) unstick the old sensor and cable, push the plug through the hole left in the casing, stick the new sensor on and you're done in 5 minutes. To give extra strength you may wish to put a blob of silicone or similar around the hole to stop you accidentally pulling the wires off the sensor. Unfortunately we could not source a gromit to do this at the moment although we are still looking!!

 

Cymbal Cables FAQ's

  • Will this fit my drumkit?

These cables will fit either the left or right cymbals on the Guitar Hero Band Hero drum kit (Circular Cymbals)

  • Is this kit compatible with the World Tour drum kit?

No

  • Do I get instructions with my order?

No, the instructions above should be sufficient even for a novice but we are always available for email support.

  • Do I need any special skills to fit this item?

No, if you can operate a screwdriver you will be fine to fit these!

  • What tools will I need?

The only tool you will need is a screwdriver (either Phillips + or a Torx T10 both of which are very common sizes). The other item you may find handy is silicone or similair for securing the cables inside the cymbal.

  • Where can I get a Torx Screwdriver

Have a look at our 8 in 1 Torx Screwdriver Set

Cymbal Repair Sensor

February 6, 2013 by  
Filed under GHWT Drum Parts, Repair stuff

Buy Guitar Hero drum / Cymbal Repair Kit

Each of the cymbals contains a sensor to register the vibration made by the drummers hit, our sensors have been extensively tested and are compatible as replacements for the cymbal pads in the Guitar Hero World Tour Drum Kit but will NOT work on the Band Hero GH6 circular cymbals. The repair kits come with 1 replacement sensor & fixing pads, full detailed fitting instructions and troubleshooting advice, within half an hour you'll be wailing on the skins again like there's no tomorrow!

We are now offering a bundle deal which adds one of our 8 in 1 Torx Screwdrivers to your order for a reduced price - just choose this option from the dropdown boxes below.

 

Cymbal Sensor Repair Kit FAQ's

  • Does this work on both cymbals?

Yes, the sensors on both cymbals are exactly the same so you will not need to specify which pad you need to repair when ordering

  • Is this kit compatible with the Band Hero drum kit?

No, it will NOT work on the circular cymbals

  • Do I get instructions with my order?

Yes, you will receive instructions via email when your item is dispatched showing how to use as either a drum or cymbal sensor replacement.

  • Do I need any special skills to fit this item?

You will need to know how to use a soldering iron

  • What tools will I need to fit it?
  • Soldering Iron & Solder (15 - 30 watts) Check out offers on soldering irons
  • Screwdriver - Either a Phillips + or a Torx T10 (both are common sizes) - Our excellent 8 in 1 Torx Screwdriver sets can be added to your order using the drop down menus above.